|
Go
to ETS Main Page
Go to Systems Integrator Specialty
Products
Main Page
ETS
Electronic Technical Services Inc.
211 Conchas SE
Albuquerque, NM 87123
Phone: 505-888-3923
Fax: 505-888-3926 Toll Free: 866-700-3923
E-mail: sales1@etsnm.com
Made in U.S.A. |
Relay Boards, Timers, Universal Voltage Regulator
|
RI16 Sixteen Channel Relay
Board
16 zone relay board accepts any
voltage from 5 to 24vdc and
converts that signal into an
isolated, dry contact, normally
open output. The RI16 is
typically used to interface fire
alarm or industrial controls with
an access control or alarm
system. The RI16 can be
ordered with EOL resistors for
use in supervised alarm circuits.
- LED indicators for each
channel.
- Power: 10-25ma per
channel.
- Dimensions: W 3.00 x L
10.00
|
Call For Pricing

View
/ save timer and
relay board -1 in PDF format.
Requires Adobe Acrobat Reader
|
URM-
1, URM- 4, URM- 8 Universal Relay Modules
The URM-X series of relay boards offer system integrators an easy, truly
universal solution for
controlling hi or low current
devices such as electric locks, lights, sirens, etc with literally ANY type
of low voltage, dry contact or open collector input signals.
- Single or multi-zone electric lock,
lighting control, etc.
- Use low-current outputs from burglar alarms, fire alarms, access
systems, CCTV systems, to control hi-current devices.
5 to 24vdc power input.
Accepts these trigger types:
Open collector or open drain
Dry contact NC or NO.
TTL or CMOS levels
Any voltage from 3.3Vdc to 24Vdc
Polarity protected power input.
Each channel has its own low-dropout 5 Volt regulator
4.7K Ohm input impedance
8 Amp 120VAC form C relay output.
Jumper selectable trigger type.
Jumper selectable Invert or buffer input signal for each channel.
European-style, easy terminate, input
and output connectors.
LED status indicators for each relay.
|
New for 2007

View / save URM-X
data sheet
in PDF format.
Requires Adobe Acrobat Reader
|
ULC
- 1, ULC - 4, ULC - 8 Universal Level Converters
The ULC-X series of level converters
offer system integrators an easy, truly
universal, solution for interfacing
equipment with differing voltages, or
input and output requirements. The
ULC outputs can also directly drive low
current devices such as electric
locks, strobes, etc.
- Convert higher DC voltage levels
to lower DC voltages.
- Convert lower voltage levels
to higher voltages.
- 5 to 24vdc power input.
- Accepts these trigger types:
Open collector or open drain.
Dry contact NC or NO.
TTL or CMOS levels
Any voltage from 5Vdc to 24Vdc
- 4.7K Ohm input impedance.
- Up to 1 Amp 24Vdc sink / source
outputs
- Jumper selectable trigger type.
- Jumper selectable Invert or buffer
input signal for each channel.
- European-style, easy terminate, input
and output connectors.
- Dual LED status indicators for each
channel.
- Outputs can be set for sink only,
source only or BOTH.
|
New for 2007

View / save ULC-X
data sheet
in PDF format.
Requires Adobe Acrobat Reader
|
|
|
|
SVRB - 5, 6, 9, 10, 12, 15, 18, 24
Simple Voltage Regulator Board
The SVRB-X is a simple, low cost ,
linear voltage regulator board
designed for low current loads using available power sources. Ideal for
point of use power. It accepts regulated DC, unregulated DC or up to 24V AC
power input Voltages . Available in eight different output voltages.
- compact size
- Automatic short circuit and thermal shutdown.
- AC or DC (polarity insensitive) voltage input.
- sticky backed tape Mounting.
- Dimensions L1.25 x W1.0
|
New for 2007

View / save SVRB-X
data sheet
in PDF format.
Requires Adobe Acrobat Reader
|
DS1 Door Contact Shunt Timer
The DS1 is designed for use on
egress doors (with no card
reader) equipped with magnetic
locks or strikes, a request to exit
device such as a PIR or electric
panic bar, and a door contact
switch. After an egress signal is
received, the door contact shunt
time begins. If the door is left
open, after the timer times out,
an alarm will result. If the door
closes before the timer time
ends, the timer is automatically
reset and the contact is
re-armed.
- LED alarm indicator
- N.C. dry contact alarm
output and RTE.
- Jumper configurable for
any application.
- Easy cable run
terminations.
- Power: 12VDC @ 20mA.
- Dimensions: W 2.40 x
L2.80
|
Call For Pricing

View / save timer and
relay board -1 in PDF format.
Requires Adobe Acrobat Reader
|